Redmax CHT2300L User Manual

The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. WA

❲8❳ CHT2300B/CHT2300L1. Attach the engine to the clutch housing ofthe cutter unit. Casually fix the front 2points with the screws(.55" long)(15m

❲9❳• Gasoline is very flammable. Avoidsmoking or bringing any flame orsparks near fuel. Make sure to stop theengine and allow it cool beforerefueling

❲10❳ STARTING ENGINE • Keep the blades clear of thesurrounding as they will start movingupon starting of the engine. 1. When first starting up after

Operation ADJUSTING IDLING SPEED 1. When the engine tends to stop frequentlyat idling mode, turn the idle set screwclock-wise. 2.When the cutting bla

❲12❳Maintenance• Make sure that the engine has stoppedand is cool before performing anyservice to the hedge-trimmer. Contactwith moving cutting head o

overheated, and that this in turn couldcause the hedge-trimmer to catch onfire. Always make sure that the muffleris clean and free of wood chips, leav

Storage❲14❳Maintenance PROCEDURES TO BE PERFORMEDAFTER EVERY 100 HOURS OF USE1. Remove the muffler, insert a screwdriverinto the vent, and wipe away

❲15❳ HT2300A [HT2300L]Type············································································· Reciprocating single-sided dual bladesBlade s

❲16❳

Parts List NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/orreplacement. 2. KOMATSU ZENOAH does not warrant

Read this manual carefully to understand allsafety precautions, controls, proper operationand maintenance of your RedMax hedge-trimmers. Failure to do

Fig.1 CUTTER GROUP — HT2300A & HT2300L❲18❳Parts List

Key# Description Part Number NoteFig.1 CUTTER GROUP — HT2300A & HT2300L2300A 2300LQ’ty❲19❳Parts List 1 Right handle comp. 3883-12101 1 12 Washer 3

Fig.2 ENGINE GROUP — HT2300A & HT2300L❲20❳Parts List

Key# Description Part Number Q'ty Note1 Cylinder 5602-12110 12 Gasket, base 5500-12213 13 Bolt, M5x22 1850-12130 24 Insulator 5500-13163 15 Gaske

Fig.3 CUTTER GROUP — CHT2300B & CHT2300L❲22❳Parts List

Fig.3 CUTTER GROUP — CHT2300B & CHT2300L❲23❳Parts List Key# Description Part Number Note2300B 2300LQ’ty1 Rear handle ass’y 6845-13100 1 12 • Screw

Fig.4 ENGINE GROUP — CHT2300B & CHT2300L❲24❳Parts List

Fig.4 ENGINE GROUP — CHT2300B & CHT2300L❲25❳Parts List Key# Description Part Number Q'ty Note1 Cylinder 5602-12110 12 Gasket, base 5500-12213

THE CALIFORNIA AIR RESOURCES BOARD AND KOMATSU ZENOAH Co. ARE PLEASED TOEXPLAIN THE EMISSION CONTROL SYSTEM WARRANTY ON YOUR 1995 AND LATER LAWN ANDGA

EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY, KOMATSU ZENOAHAMERICA INC. (THE COMPANY), THROUGH ANY RedMax DEALER, WIL

CONTENTSSAFETY PRECAUTIONS · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 2PROPER AND SAFE OPERATION OF YOUR HEDGE-TRIMME

Pièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., parl'intermédiaire de n'importe quel revendeur

Emission Control LabelMade in JapanRedMaxIMPORTANT ENGINE INFORMATION THIS ENGINE CONFORMS TO U.S. EPA PH1 FOR SMALL OFF-ROAD ENGINES. ENGINE F

KOMATSU ZENOAH AMERICA INC.4344 Shackleford Road Suite 500Norcross, Georgia 30093© Printed in Japan

❲2❳ IN ORDER TO ENSURE PROPER AND SAFEOPERATION OF YOUR HEDGE-TRIMMER• This product has been designed for use intrimming leaves and branches from tree

Safety Precautions WORK GEAR AND CLOTHING• When using your hedge-trimmer, always besure to wear strong, durable, work clothing;shirts should be long-

❲4❳Safety Precautions THINGS TO CHECK BEFORE USING YOURHEDGE-TRIMMER• Before beginning work, look aroundcarefully to get a feel for the shape of thela

• Never touch the spark plug or plug cordwhile the engine is in operation. Doing somay result in being subjected to anelectrical shock.• Never touch t

Safety Precautions❲6❳ NOTES ON CARE AND MAINTENANCE OFYOUR HEDGE-TRIMMER• In order to maintain your hedge-trimmer inproper working order, perform them

Set up HT2300A/HT2300L1. Join the engine unit to the clutch housingof the cutter unit, with the fuel tank on theblade side. 2. Align the mounting hol