RedMax BT225 Specifications

OWNER/OPERATOR MANUALLINE TRIMMERBT01-00000(201)The engine exhaust from this productcontains chemicals known to the Stateof California to cause cance

❲10❳Never place the throttle into the high speedposition when starting the engine.3. After starting the engine, check to make surethat the cutting att

• IF SOMEONE COMES1. Guard against hazardous situations at all times.Warn adults to keep pets and children awayfrom the area. Be careful if you are ap

❲12❳5. For safe operationrefill the tank of the unit in any place where thereis a boiler, stove, wood fire, electrical sparks,welding sparks, or any o

MOUNTING ENGINE (SE1)1. Loosen the bolts temporarily attached to theclutch housing.2. Push the driveshaft toward the gearcase androtate it by hand t

❲14❳6. Set up INSTALLING CUTTING HEAD (SE6)1. While locking the gear shaft by inserting theattached bar into the upper holder and thehousing. 2. Rota

• Gasoline is very flammable. Avoid smokingor bringing any flame or sparks near fuel.Make sure to stop the engine and allow itcool before refueling t

❲16❳at least one minute.5. Put a clear indication on the outside of thecontainer to avoid mixing up with gasoline orother containers.6. Indicate the c

STARTING ENGINE1. Rest the unit on a flat, firm place. Keep thecutting head off the ground and clear ofsurrounding objects as it will start rotating

❲18❳8. Operation STOPPING ENGINE1. Release the throttle lever and run the engine fora half minute.2. Shift the ignition switch to the STOP position.•

3. You can avoid thrown debris by sweeping fromyour left to the right.4. Use a slow, deliberate action to cut heavygrowth. The rate of cutting motion

❲20❳9. Maintenance• Always be sure to stop the engine before inspecting the brushcutter for problems orperforming maintenance.• Never alter the brushc

❲21❳9. Maintenance8 11 1412910 121315THISSIDE UPTHISSIDE UPWINDLINE

❲22❳• Make sure that the engine has stopped and iscool before performing any service to thebrushcutter. Contact with moving cuttinghead or hot muffler

MUFFLER• Inspect periodically, the muffler for loosefasteners, any damage or corrosion. If anysign of exhaust leakage is found, do not usethe brushc

❲24❳9. Maintenancebrushcutter. Note that it is necessary to removethe plug guard shown in Figure 20 in order to beable to view the upper part of the c

10. Storage• Aged fuel is one of major causes of enginestarting failure. Before storing the unit, empty thefuel tank and run the engine until it uses

❲26❳11. Troubleshooting guideCase 1. Starting failure CHECK PROBABLE CAUSES ACTIONfuel tank ➞ incorrect fuel ➞ drain it and with correct fuelfuel filt

12. Parts list NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/orreplacement. 2. KOMATSU ZENOAH does not warr

12. Parts list ❲28❳Fig.1 DRIVE UNIT BT225 (S/N 000001 and up)

Key# Description Part Number Q'tyFig.1 DRIVE UNIT BT225 (S/N 000001 and up)Key# Description Part Number Q'ty1 PIPE COMP. BT01-50810 12 DRIV

SAFETY FIRSTInstructions contained in warnings within thismanual marked with a symbol concerncritical points which must be taken intoconsideration to

Fig.2 ENGINE UNIT BT225 (S/N 200101 and up)❲30❳12. Parts list

Key# Description Part Number Q'tyFig.2 ENGINE UNIT BT225 (S/N 200101 and up)❲31❳Key# Description Part Number Q'ty1 CYLINDER 5580-12110 12 G

The California Air Resources Board and KOMATSU ZENOAH are pleased to explain theemission control system warranty on your 1995 and later small off-road

EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE UNIT, KOMATSU ZENOAH AMERICA INC. (THE COMPANY), THROUGH ANY RedM

Pièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., parl'intermédiaire de n'importe quel revendeur

KOMATSU ZENOAH AMERICA INC.4344 Shackleford Road Suite 500Norcross, Georgia 30093© Printed in Japan

2. Specifications BT225Overall size(LxWxH)························································ 70.0(1780)x14.0(355)x9.5(241) in(mm)Dry weight w/o

(1) Read owner's manual before operating this machine.(2) Wear head, eye and ear protection.(3) Warning/Attention(4) Keep all children, bystander

❲6❳For safe operation and maintenance,symbols are carved in relief on the machine.According to these indications, please becareful not to make a mista

❲7❳5. For safe operation1. Read this manual carefully until youcompletely understand and follow all safetyand operating instructions. 2. Keep this man

❲8❳b. At night, at times of heavy fog, or at any othertimes when your field of vision might belimited and it would be difficult to gain a clearview of

BEFORE STARTING THE ENGINE1. The area within a perimeter of 50 feet (15m) ofthe person using the product should beconsidered a hazardous area into w